Not sure which NeoSander sanding head is right for your project? Should you reach for a flat, curved, pointed, or angled head?

The answer depends on the surface you need to sand. A broad panel, narrow groove, rounded edge, and inside corner each require a different contact shape.

This guide explains how to choose and use all eight NeoSander sanding head shapes. You’ll compare their key dimensions, see where each one works best, and learn how to keep the same sanding head shape as you move through different grits.

Hand using a NeoSander detail sander on a grey 3D printed model, with all eight sanding head shapes lined up below

1. Quick Guide: Choose the Right NeoSander Sanding Head

First, look at the shape of the area you want to sand. Then check how much space is available. The sizes below describe the sanding end of each sanding head, not its mounting section or total length.

NeoSander sanding head comparison
Sanding head Example Best for Key sizes*
01 Pointed Tip NeoSander Pointed Tip sanding head sanding a small detailed area Small details, narrow grooves, tapered spaces, and recessed areas Sanding area: 19.0 mm L × 6.2 mm max. W
Tip angle: 30°
Max. height: 10.7 mm
02 Flat (Slim) NeoSander Flat Slim sanding head sanding a narrow flat surface Narrow flat surfaces, thin edges, and straight grooves Sanding area: 19.0 × 3.1 mm (L × W)
Max. height: 10.7 mm
03 Flat (Medium) NeoSander Flat Medium sanding head sanding a medium flat surface Medium flat surfaces and edges Sanding area: 19.0 × 6.2 mm (L × W)
Max. height: 10.7 mm
04 Flat (Large) NeoSander Flat Large sanding head sanding a broad flat surface Large, open flat surfaces Sanding width: 12.4 mm
Max. height: 10.7 mm
05 Half-Cylinder NeoSander Half-Cylinder sanding head sanding a curved groove Semi-circular grooves, curved edges, and rounded details Sanding length: 19 mm
Width × depth: 5.8 × 4.5 mm
Max. height: 11.7 mm
06 Arc NeoSander Arc sanding head sanding a broad curved surface Arcs, rounded corners, and broad curved surfaces Sanding length: 19 mm
Width × depth: 10.3 × 2.9 mm
Max. height: 12.7 mm
07 Acute Angle (45°) NeoSander 45-degree sanding head sanding a V-shaped groove 45° V-shaped grooves and narrow inside angles Sanding length: 19 mm
Angle: 45°
Depth: 7.0 mm
Max. height: 13.7 mm
08 Right Angle (90°) NeoSander 90-degree sanding head sanding an inside corner 90° inside corners and square joints Sanding length: 19 mm
Angle: 90°
Depth: 4.4 mm
Max. height: 13.7 mm

Sanding length is measured along the sandpaper from its base to its tip. Sanding width is measured from side to side.

Max. head height is the tallest point of the sanding head. If the entire sanding head needs to fit inside an opening, the opening must be larger than this measurement, with extra clearance for the sandpaper, working angle, and back-and-forth movement.

Looking for the complete tool? See NeoSander and its eight included sanding heads.

2. Check the Fit Before You Start

Step 1: Look at the Area You Need to Sand

Do not choose a sanding head based only on the overall shape of the part. Look closely at the exact area you need to sand. Is it flat, curved, narrow, pointed, or inside a corner?

One part may need several sanding head shapes. For example, you may use a Flat sanding head on a panel and an Angle sanding head in a nearby corner.

Step 2: Use the Largest Sanding Head You Can Control

A larger sanding head can cover an open surface more evenly and efficiently. A smaller sanding head provides better access around edges, grooves, and nearby details.
Choose the largest sanding head that matches the surface and remains easy to control. It does not always need to sit completely inside the target area, but it should have enough support to stay stable and avoid touching surfaces you want to preserve.

Step 3: Test the Fit with NeoSander Switched Off

Place the sanding head against the part before switching on NeoSander. Check three things:

  1. Does the sanding surface sit firmly on the target area?
  2. Could the sanding head touch a nearby edge, wall, or detail?
  3. Is there enough space for the sanding head to move back and forth?

This check is especially important inside grooves and recessed areas. A sanding head may fit into the opening but still have too little space to move safely.

3. How to Use Each Sanding Head

Pointed Tip Sanding Head: Use Light Pressure and Short Passes

Use the Pointed Tip sanding head for small details, narrow grooves, recessed areas, and spaces that become narrower toward the end.

Because the pointed tip concentrates pressure on a small area, it can remove material quickly or create a low spot if it remains over one place for too long. Use light pressure and guide the sanding head in short, controlled passes. Avoid dwelling on the same spot.

If the target area is flat and wide enough, use the Flat (Slim) sanding head instead. Its wider contact area will usually feel more stable.

Flat Sanding Heads: Keep the Contact Flat and Stable

Flat (Slim), Flat (Medium), and Flat (Large) work best when the sanding surface stays parallel to the workpiece and the contact remains stable.

Use the widest Flat sanding head that fits completely within the target area. If part of the abrasive face extends beyond the workpiece, the reduced support can make the sanding head easier to tilt and concentrate pressure on the edge. Switch to a smaller Flat sanding head for more stable contact and a lower risk of rounding the edge.

If the sanding head still cannot sit evenly on the surface, Half-Cylinder or Arc may be a better match.

Half-Cylinder and Arc Sanding Heads

Use the Half-Cylinder and Arc sanding heads on curved areas. With NeoSander switched off, place each sanding head against the workpiece and see which profile matches the curve more closely.

Choose the sanding head that sits steadily against the surface. The curved sanding face should make broad, even contact rather than touching only at the center or one edge. If the contact area is too small, do not press harder. Try the other curved sanding head or adjust your working angle.

Guide NeoSander along the curve with light, overlapping passes. Check the workpiece from several angles so you can spot an unwanted flat area before removing too much material.

45° and 90° Angle Sanding Heads

With NeoSander switched off, check that both abrasive faces of the Angle sanding head sit evenly against the two sides of the inside corner.

Use light, centered pressure so both sides sand evenly. Do not force the sanding head deeper into the corner, as this can remove too much material or cause one face to sand more aggressively than the other.

If you need to sand only one side of the corner, use a suitable Flat sanding head for better control.

Chart comparing recommended and not recommended use of NeoSander pointed tip, flat, curved and angled sanding heads

Custom Sanding Heads

The eight standard sanding heads cover many common sanding tasks. If your project requires a different contact shape, you can also explore the 3D-printable NeoSander sanding head designs on HOZO’s MakerWorld profile.

Before printing or using a custom sanding head, check the compatibility, material, printing, and installation instructions provided on its model page.

4. A Simple NeoSander Workflow

Good sanding comes from working in small, controlled steps. Heavy pressure is usually not needed.

  1. Remove large bumps first. Trim large support marks, sprue marks, or extra material before sanding. Do not cut so close that you damage the part.
  2. Choose the sanding head. Match the sanding head shape to the area you want to sand.
  3. Attach the sandpaper and check the fit. If the sandpaper is already attached, make sure it is flat and secure. With NeoSander switched off, check that the sanding head contacts the correct area and has enough space to move.
  4. Set the stroke and start sanding. NeoSander’s stroke length can be adjusted from 0.6 to 1.8 mm. Start with a shorter stroke near edges, corners, and small details. Use light pressure and short, controlled passes. Check the surface often to avoid removing more material than needed.
  5. Clean and inspect the surface. Remove sanding dust and check your progress often. Before moving to a finer grit, make sure the main defect and the scratches from the previous grit have been removed.

Safety note: Wear suitable eye and breathing protection, control sanding dust, and secure the part before sanding. Always follow the safety instructions for the tool and the material.

To learn more about stroke settings, read Why Adjustable Stroke Length Makes Detail Sanding Easier.

5. Keep the Sanding Head Shape, Change the Grit

Once you find a sanding head shape that fits the area, keep using the same shape as you move through different grits. This helps the sanding head contact the surface in a consistent way.

For example, if Flat (Slim) fits a narrow edge, you could use it with #240 to remove the main defect, then switch to Flat (Slim) in #400 and #600 to smooth the surface.

The right sandpaper grit depends on the material, the defect, and the finish you want. For detailed advice, read How to Choose the Right Sandpaper Grit.

The Idea Behind the 8 × 8 Color-Coded System

With a basic set of eight sanding heads, changing grit may require removing the sandpaper and attaching a new piece. This works well for occasional sanding, but it can slow down projects that use several grits.

NeoSander’s 8 × 8 color-coded system combines eight sanding head shapes with eight sandpaper grits. The result is a collection of 64 sanding heads, with one color for each grit.

Instead of replacing the sandpaper at every stage, you can switch to the same sanding head shape with the next grit already attached. This saves time, keeps the sanding head shape consistent, and makes each grit easier to identify.

The Basic Sanding Head Collection is suitable for occasional grit changes. The 64-piece Multicolored Sanding Head Collection is better suited to regular multi-grit sanding, repeated projects, and batch work.

NeoSander detail sander used on a small 3D printed figure next to a 64-piece multicolored sanding head case on a cutting mat

6. Start with the Right Fit, Then Adapt

Choosing the right sanding head is not about finding one head for the entire project. Match each area with the sanding head that makes stable contact, stays clear of nearby details, and has enough room to move. Once you find the right shape, keep it consistent as you move through the grit sequence.

The eight standard sanding heads provide a practical starting point, not a fixed set of rules. As you learn how each shape behaves, you can adjust your technique or create a custom sanding head for a specific task. The goal is always the same: a setup that fits the surface and gives you good control.

7. Frequently Asked Questions

Which Flat sanding head should I start with?

Start with the largest Flat sanding head that fits completely on the target area without touching nearby details. Use Flat (Large) for broad surfaces, Flat (Medium) for general flat areas, and Flat (Slim) for narrow surfaces and tight spaces.

If a sanding head fits inside an opening, does that mean it is suitable?

Not necessarily. The sanding head also needs enough space for the sandpaper, your working angle, and its back-and-forth movement.

Test the fit with NeoSander switched off. Make sure the sanding head can move without touching the sides of the opening or nearby details.

Should I use Pointed Tip or Flat (Slim) in a narrow area?

Use Flat (Slim) on a narrow but regular flat surface. Its straight sanding area provides more even contact.

Use Pointed Tip when the space becomes narrower, ends in a small detail, or cannot be reached by a straight Flat sanding head.

What is the difference between Half-Cylinder and Arc?

Use Half-Cylinder for semi-circular grooves, curved edges, and smaller rounded areas. Use Arc for broader curves and rounded corners.

Test both sanding heads with NeoSander switched off. Choose the one that follows the curve more closely and sits firmly without rocking.

Should both sides of an Angle sanding head touch the corner?

Yes, when you want to sand both sides of the corner evenly. Place both sanding surfaces against the corner and use light, centered pressure.

If you only want to sand one side, use a Flat sanding head for better control.

Should I keep the same sanding head shape when changing grits?

Yes, whenever possible. Keeping the same sanding head shape helps maintain a similar contact area and sanding angle as you move from a coarser grit to a finer one.

With the 8 × 8 color-coded system, you can switch to the same sanding head shape with the next grit already attached.

Do I need to use every grit from #180 to #1500?

No. Start with the finest grit that can remove the defect efficiently, then move to finer grits as needed.

You do not need to begin with #180 for light surface marks, and you do not need to finish with #1500 if the surface is already suitable for the next step.

Latest Stories

This section doesn’t currently include any content. Add content to this section using the sidebar.