10 produkter

NeoBlock Premium Combo

Reapris¥12,320 JPYOrdinarie pris ¥15,400 JPY

NeoBlock Combo

Reapris¥4,560 JPYOrdinarie pris ¥5,700 JPY

Slipbandsset

Reapris¥7,840 JPYOrdinarie pris ¥9,800 JPY

NeoBlock-slipkloss

Reapris¥2,080 JPYOrdinarie pris ¥2,600 JPY

Slipband med kornstorlek 180

Reapris¥1,600 JPYOrdinarie pris ¥2,000 JPY

Slipband med kornstorlek 120

Reapris¥1,600 JPYOrdinarie pris ¥2,000 JPY

Slipband med kornstorlek 400

Reapris¥1,600 JPYOrdinarie pris ¥2,000 JPY

Slipband med kornstorlek 240

Reapris¥1,600 JPYOrdinarie pris ¥2,000 JPY

Slipband med kornstorlek 800

Reapris¥1,600 JPYOrdinarie pris ¥2,000 JPY

Slipband med kornstorlek 600

Reapris¥1,600 JPYOrdinarie pris ¥2,000 JPY

Skapa enkelt med HOZO

Internationell frakt

Fri frakt på beställningar över 180 $

1 års garanti

14 dagars problemfria returer

Most sanding blocks are a shape wrapped in paper. When the paper wears, the block goes in the bin. NeoBlock separates the two: an ergonomic aluminum-and-steel handle you keep, swappable heads for different geometry, and a belt that slips off and on when it is spent.

The handle with the S01 basic head measures 122 × 32 × 24 mm (4.8 × 1.26 × 0.94 in) and is built from PC+ABS, aluminum alloy, stainless steel and manganese steel. Belts are 32 × 280 mm (1 1/4 × 11 in) on an industrial cloth backing.

Choose Your NeoBlock Setup

  • NeoBlock Sanding Block the handle, one S01 basic head and one 400-grit belt. The starting point for flat surfaces, rounded corners and everyday maker work.
  • NeoBlock Combo adds the S02 Pro and S03 Expert heads plus a six-in-one belt sampler with one belt of each grit: #120, #180, #240, #400, #600 and #800.
  • NeoBlock Premium Combo the three heads with the full Sanding Belt Set rather than the sampler, for people who sand often enough to run through grits.

The choice comes down to geometry and volume. One head covers flat work. Three heads let you move between flat surfaces, concave curves and convex curves without changing tools. The sampler tells you which grits you actually reach for; the full set is what you buy once you know.

Heads And Belts

Each head presents a different profile to the work. S01 Basic is for flat surfaces and gentle radii. S02 Pro reaches into concave curves, corners and grooves. S03 Expert follows convex curves and cleans up support marks, burrs and layer lines on 3D prints. All three take the same 32 × 280 mm belt, so grit and geometry are independent choices.

Belts are sold in 10-piece packs by grit — #120, #180, #240, #400, #600 and #800 — or as the 60-piece Sanding Belt Set covering the full range.

How To Work Through The Grits

Use the coarsest grit only where you genuinely need to remove material, then step up. Each finer grit is there to erase the scratch pattern the previous one left, not to remove more stock. Skipping two grades usually costs more time than it saves, because the deeper scratches keep surfacing. How to choose the right sandpaper grit gives the practical ranges for wood, plastic, resin, metal and 3D prints.

Light pressure beats heavy pressure on small parts. Leaning on a block removes an edge before you notice it has gone — especially on printed parts where a chamfer is only a fraction of a millimeter deep.

Block Or Powered Sander?

A block gives you direct feedback: you feel the surface change under your hand, which is what you want on a delicate edge or a final blending pass. A powered sander is faster on repetitive work — a batch of parts, a long run of layer lines, or areas that would be tiring to finish by hand. Many people keep both: NeoSander for the bulk work, NeoBlock for the last visible corrections. The comparison is set out in detail sander vs sanding stick.

Finishing Guides

Frequently Asked Questions

What size sanding belts does NeoBlock use?

NeoBlock uses 32 × 280 mm (1 1/4 × 11 in) belts on an industrial cloth backing. The same belt size fits all three sanding heads.

What is the difference between the S01, S02 and S03 heads?

S01 Basic is for flat surfaces and gentle radii. S02 Pro is for concave curves, corners and grooves. S03 Expert is for convex curves and for cleaning up support marks, burrs and layer lines on 3D prints. All three fit the same handle and take the same belt size, so you can change geometry without changing grit.

Which NeoBlock setup should I start with?

Start with the base NeoBlock if you mainly sand flat surfaces. Choose the Combo if you want all three heads and a sampler to find out which grits you use. Choose the Premium Combo if you already sand regularly and want the full belt set rather than one of each.

Do I still need a powered sander if I have NeoBlock?

Not necessarily. A block is better for direct control on delicate edges and final blending. A powered detail sander such as NeoSander is better for repetitive work across many parts or long runs of layer lines.